Spare Parts

Convert your remote extruder to a direct drive extrusion using this plate and the required spacer.

Use all other existing parts (Rollers, Screws, etc...

Suitable for 2020 profile

Heat Cartridge

Voltage : 24V DC

Power : 40 W

Cable length : 120 cm / 1200mm

Features

High Temperature Resistance.

The XS series tubing is made with the highest quality ptfe. It is able to withstand even higher temperature which is up to 300°C as compared to other ptfe tube in the market.

High Lubricity Additives property make their XS Series tubing the lowest friction Bowden tubing on the market. Less friction means higher responsiveness, higher accuracy prints and smoother feeding.

1.9mm Inner Diameter. It is designed for 1.75mm filament as smaller inner diameter gives greater feeding accuracy. Besides, this also makes it easy to print flexible filaments even on the longest Bowden systems.

Contact us if you need smaller than 1 meter

Size 480 x y600 x 720 mm

Suitable for small & medium 3d printers

Creality Fireproof and Dustproof

Helps to keep constant temperature

Protective Cover Room

Allows you to print ABS and temperature sensitive materials

Suitable for Ender5 Plus/5/5 pro/3 Max,CR-10/10V2/10 V3/10S/10S PRO/10S PRO V2/10MINI,CR-X/CR-20/20PRO

Size 700 x 750 x 900 mm

Suitable for most large 3d printers

Creality Fireproof and Dustproof

Helps to keep constant temperature

Protective Cover Room

Allows you to print ABS and temperature sensitive materials

Suitable for Ender5 Plus/5/5 pro/3 Max,CR-10/10V2/10 V3/10S/10S PRO/10S PRO V2/10MINI,CR-X/CR-20/20PRO

No Edge Curling - 3D printer coated glass bed, molds could stick on bed firmly without glue, avoiding the issue of print edges curling.

No-indentation Printing - Upgraded Ender 3 glass plate has a much smaller CREALITY logo than older version, avoiding leaving logo indentations on molds surface during 3D printing.

Excellent Flatness - Improved 3D printer glass plate provides more flat and more smooth build surface than magnetic mat or PEI sticker, ensuring high flatness for the bottom of model.

Super Convenient - Very easy to take off the model, no tools needed. Automatically pops up when cold

This borosilicate glass bed could be fixed with middle sized clips and cleaned with alcohol or acetone at room temperature.

Compatibility - The 3D printer parts is applicable with Creality 3D printer Ender-3, Ender-3 Pro, Ender-3S, Ender-3X, Ender-3 V2, Ender-5, Ender-5 Pro and CR-20, CR-20 Pro. Suitable for other printer brands having the same size

This breakout board for Allegro’s A4988 micro-stepping bipolar stepper motor driver features adjustable current limiting, over-current and over-temperature protection, and five different micro-step resolutions (down to 1/16-step). It operates from 8 V to 35 V and can deliver up to approximately 1 A per phase without a heat sink or forced air flow (it is rated for 2 A per coil with sufficient additional cooling)

1. A simple steps and direction control interface

2 six different steps resolutions: full step, half step, 1/4-step1/8-step1/16-step, 1/32-step

3 CAN interface directly with 3.3 V and 5 V systems

4 Over-temperature thermal shutdown, overcurrent shutdown, under-voltage lockout

5 short to ground short circuit load protection

6 4 Layer 2 oz copper PCB, in order to improve heat dissipation

7 exposed solder ground below the bottom of the driver IC on the printed circuit board pad

8 module size, pin and interface matching A4988 stepper motor driver operators in many ways

9 adjustable current control lets you set a potentiometer, which lets you use the stepper motor's rated voltage or more, in order to achieve a higher rate of maximum output current step

10 Intelligent chopping control automatically selects the correct current decay mode (fast decay or slow decay)

11 Maximum 45 V supply voltage

Output current: 40A

input 3-32vdc

output 5-60vdc

Control Method: dc-dc

• Product size: 20mm (width) x33 (length)   
• Made from polyimide film with silicone adhesive. Heat Tape are compatible with a wide temperature range as low as -73°C (-99°F) and as high as 260°C (500°F) Leaves no residues
• Primarily used to hold transfer sheets in place while sublimating onto a variety of items and hold the polymer plate on the heating platen in hot foil stamping. Excellent heat & solvent resistance Minimal shrinkage after baking and clean removal.
• High performance, reliability and durability, with a unique combination of electrical, thermal, chemical and mechanical properties
• Ideal for protecting sensitive printed circuit board (PCB) components such as gold leads and gold fingers during the process of wave soldering. Also extensive use as electrical insulation for transformer, motor, coil, capacitor and frequency conversion power supply in electronic industry.

• Product size: 20mm (width) x33 (length)   
• Made from polyimide film with silicone adhesive. Heat Tape are compatible with a wide temperature range as low as -73°C (-99°F) and as high as 260°C (500°F) Leaves no residues
• Primarily used to hold transfer sheets in place while sublimating onto a variety of items and hold the polymer plate on the heating platen in hot foil stamping. Excellent heat & solvent resistance Minimal shrinkage after baking and clean removal.
• High performance, reliability and durability, with a unique combination of electrical, thermal, chemical and mechanical properties
• Ideal for protecting sensitive printed circuit board (PCB) components such as gold leads and gold fingers during the process of wave soldering. Also extensive use as electrical insulation for transformer, motor, coil, capacitor and frequency conversion power supply in electronic industry.